⎝⎛pt电子游戏⎞⎠

Welcome to the official website of Gongyi Hongyun Machinery Manufacturing Co., Ltd.!
#
24-hour service hotline
0371-69573555
Fortune Product Center
product center
Pneumatic conveying Gray library section Mechanical conveying Dry desulfurization technology and complete system
Contact us
#

Phone: 0371-69573555

Hotline: 13849069519

Fax: 0371-69574567

Email: ab69574567@163.com

Address: No. 2 Baisha Road, Gongyi City, Henan Province

#

Air conveying chute

XZ type air conveying slant is suitable for conveying easily fluidized powdery materials such as cement. It is not suitable for materials with large particle size, high moisture content and poor fluidization performance. This tank uses high pressure centrifugal fan (9-19: 9-26) as the power source, so that the materials in the chute can be conveyed in a closed way.

适用有于输送水泥等易流态化粉状物料,对粒度大、水分多、流态化性能差的物料不宜使用。 XZ type air conveying slant is suitable for conveying easily fluidized powdery materials such as cement. It is not suitable for materials with large particle size, high moisture content and poor fluidization performance. This tank uses high-pressure centrifugal fans (9-19: 9-26) as the power source, so that the materials in the closed conveying chute can be kept fluidized and flow slowly to the inclined downward end. The main part of the machine has no transmission parts, convenient sealing operation and management, light weight equipment, low power consumption, large conveying capacity, easy to change the conveying direction, and the use of new coatings and breathable layers.

installation:
1. Generally, the straight-line conveying, installation and discharge of materials are inclined 6-10 degrees downward, and the upper and lower grooves and the joints between the grooves are sealed reliably (add pads).
2. Need to turn 90 degrees (about minutes)
3. It is necessary to use a three-way slot or a four-way slot for bifurcation and load the air valve after the bifurcation. In order to control the flow of fluidized materials, to ensure that the material "allows air", the decommissioning section can reduce the air consumption.
的耗气量计算公式如下: 4. The calculation formula for the air consumption of the side of the lower tank after the transmission line is too long or branched, and the air chute of the fan is added as follows:
V = 60 × α ×× L where V—gas consumption m3 / h; α—gas consumption per unit area of the ventilation layer is generally 2.0--3m3 / m2 min; B—chute width mm; L—chute length m .
5. The chute exhaust air is exhausted from the tank on the discharge tank. After passing through the exhaust pipe, it should enter the small bag dust removal port. The air volume is 1.5 times the required air volume. about.

Use and maintenance:
1. Turn on the fan before feeding when starting up, stop feeding when shutting down, stop the fan after the material is delivered (or close to it), and stop the fan when it is not in use;
2. The conveying trough should be kept sealed, and if there is air leakage or powder leakage, it should be overhauled;
3.When replacing the polyester breathable layer
a. Cut, cut the breathable layer according to the required size, and use an electric iron (or heated steel bar) to heat and block the cut to prevent diffusion;
b. Make holes, heat with iron rods that are slightly smaller than the diameter of the mounting bolts, and perforate the parts around the breathable layer that need to be perforated. When perforating, be careful not to allow the open flame to burn out the ventilation layer. If you use a drill to drill holes, use a hot iron rod to iron the area around the hole after the drill to prevent it from falling apart.
c. Lay the breathable layer on the punching box, pass through the bolts, add iron bars around it to compress it, and tighten the screw to use.
d. Beads (or flanges) should be depunctured and the welds worn out;
e. In order to ensure sealing, polymer sealant (or 10 mm thick felt pad) can be applied around the lower surface of the breathable layer.

Technical Parameters:
project
model
200
250
315
400
500
Tank body width
200
250
315
400
500
Produce

the amount

t / h

8 °
cement
twenty two
40
70
130
220
Raw material
16
30
55
100
165
10 °
cement
40
65
120
250
400
Raw material
30
55
90
185
300
Wind pressure KPa
3--4
Air volume m3 / m2.min
1.5--2

Gongyi Hongyun Machinery Manufacturing Co., Ltd. is a modern enterprise integrating research, design and manufacturing. The company is mainly engaged in the research and development and manufacture of pneumatic conveying of powder materials and supporting equipment for ash storage. 输粉机 、粉煤灰气力输送系统,石灰石粉气力输送系统、粉料输送泵、 喷射输送泵 返灰泵 干灰散装机 双轴加湿搅拌机 DMC脉冲布袋除尘器 真空压力释放阀 手动插板阀 电动给料机(锁气器)、 气动圆顶阀、 自动双侧库底卸料器等气力输送系统及灰库配套设备。 Main products: material sealing pump , powder conveyor , fly ash pneumatic conveying system, limestone powder pneumatic conveying system, powder conveying pump, jet conveying pump , ash return pump , dry ash bulk machine , double shaft humidifying mixer , DMC pulse cloth bag Pneumatic conveying systems such as dust collectors , vacuum pressure release valves , manual plug-in valves , electric feeders (air locks), pneumatic dome valves, automatic double-side warehouse bottom unloaders and ash warehouse supporting equipment. For product details, please call 0371-69573555, can provide you with complete pneumatic conveying and ash storage supporting system excellent solution!

Related Products


  • Level gauge

    Level gauge

  • Screw pump

    Screw pump

  • Manually switch the tee

    Manually switch the tee

七乐彩 欢乐拼三张 欢乐拼三张 真人游戏平台注册